1.啟動山東裝載機，就近尋找一塊比較平坦開闊的場地，壓下動臂升降桿，利用動臂支承使前輪離地，然后用支架支撐在閃橋靠近爆胎的一側，并將后輪楔好。Shandong boot loader, find the nearest one site is relatively flat and open, under the pressure of the boom lifting rod, the movable arm supporting the front wheels off the ground, and then use the support in the bridge near the tire side flash, and rear wheel wedge.

2.利用撬杠等等工具，拆卸擋圈及鎖圈然后檢查輪胎襯墊與輪輞外表面是否粘連。若發生可撤掉支撐物，使山東裝載機在短距離內慢速往復運行，直至襯墊與輪輞外表面脫離；嚴禁轉向和高速行駛，以免損壞內胎。然后，前輪重新支撐起來。Use a crowbar, and removing the retainer ring lock ring and then check the tire and rim liner outer surface adhesion. If there can be removed support, make Shandong loader running slow reciprocating within a short distance, until the liner and the outer surface of the rim from the forbidden; steering and high speed, so as to avoid damage to the tube. Then, the front wheel to prop up.

3.將山東裝載機內、外胎的相對位置作好標記，以便查找、清除異物和修補輪胎。The relative position of Shandong, the loader tire mark, in order to find and remove foreign bodies and tire repair.

4.利用撬杠等工具，將山東裝載機輪胎從輪輞上拆下。注意，動作要輕柔配合要默契，避免被輪胎砸傷，并且要保護好氣門嘴。Use the crowbar and other tools, will Shandong loader from tire rim removed. Note that the action should be gentle with the tacit understanding, to avoid being injured and protect the tire, aerobic door mouth.

5.山東裝載機外胎被釘子等細長異物扎傷后，若表面無明顯創口或創口較小，則此外胎可繼續使用(因?yàn)檠b載機輪胎屬低壓胎，且運行速度比較慢)；若創口較大，則必須進行修補(因?yàn)闄C(jī)器運行時，輪胎受擠壓磨擦，時間一長就會損壞內胎，甚至創口越來越大、內胎突出，造成輪胎報廢)。Shandong tire loader is slender nail foreign body after injuries, if the surface has no wound or the wound is small, the tyre can continue to use (because the loader is a low pressure tire tread, and the running speed is relatively slow); if the wound is large, it must be repaired (because when the machine is running, the tire friction would be squeezed, long time tube damage, even more and more prominent, the wound tube, causing scrap tire).

6.若是新內胎，必須將氣門嘴底部的螺栓擰緊，以防漏氣；然后將外胎內腔的異物清除，并撒入適當?shù)幕郏磕ň鶆颉榱耸挂r墊與內、外胎貼緊，在山東裝載機裝入內胎后應給內胎適當充氣，再塞入襯墊。If the new tube, must tighten valve at the bottom of the bolt, to prevent leakage; then the tyre cavity foreign body removal, and sprinkle with appropriate talcum powder, evenly. In order to make the inner liner and tyre tightly, loader into the tube in Shandong should give appropriate air into the liner tube, then.

7.將山東裝載機輪胎裝到輪輞上，裝上鎖圈、擋圈；安裝過程中要保護好氣門嘴。Shandong loader tires mounted on the rim, fit a lock ring and the retainer ring; the installation process to protect the aerobic door mouth.

8.用車載空壓機給山東裝載機輪胎充氣。Charging of Shandong loader tire with vehicle air compressor.

9.壓下動臂升降桿，取出支架；至此山東裝載機換胎完畢，整個過程大約需要50min。更換后輪胎時，則需要另一臺山東裝載機或者其他起重設備輔助，將后輪胎支撐起來，其他程序則與更換前輪胎相同。Out of the bracket arm lifting rod, under pressure; thus Shandong loader tires is completed, the entire process takes about 50min. Replacement of the tires, you need another Shandong loader or other lifting equipment auxiliary, the rear tire support, other procedures and replacement of the same tire.